Видео

Just purchased mine, hopefully the fence issue has been dealt with, if not, make me own fence

Really appreciate the tip, mate.

Maybe show the end result more than 1/5th of a second?!?

Great stuff mate, but i think i got auto corrected in the member list 😂 -- Fixed Fingers

Thank you for making this video. I think I finally know how to fix the fridge door that has been wobbly for over two years! You make it look very easy! Thanks!

The bit you missed out was checking the back of the blade for fused on rubber from the track. My blade went out of balance because of it. You might need a bit of white spirit or some other solvent to get it off. Bit of a design flaw if you ask me.

Hey Karl. Good video. I have to build an Urn for my wife. I like the fact that you give instructions on what you are doing. Most guys just show them building an Urn. That teaches me nothing. I will use your video to guide me in building my wife's Urn. Thanks for sharing.👍👍🍁

Say it as it is Karl, spot on mate

Great tip Karl

Nice cut, Karl

Top Job Karl

❤❤❤❤❤❤❤❤❤❤❤

Quality tradesman, excellent work 👏

Pro ish my arse thats a complete Pro job. Pro ish is my attempt at what am doing just now kicking my arse and at 65 quid a sheet for the 9mm mdf kinda puckering my arse doing it as well 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

What happens if is splits after being in a house

👍👍👍. Thank you Karl

Could've been perfect if only you took your time. Why use such a thick pencil line and not lay it up properly? I don't understand woodworkers at all.

Nice job m8 cabinet looks wicked 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

Very nice build Karl, keep it up matey

Not a good job. Lol Measuring tape does it just fine. Did you get some tools for a present. 10min job. I must have taken you ages.

Another great video Karl.

Really enjoyed that. Cheers Karl. Good to see you on YT

Not watched the entire video yet but so far you have used 9 electric tools to make this.

Hes back 😁 nice see you back m8 wicked build and good see am not the only one rocking the hairy chicken legs and shorts 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿😉

Great looking cabinet mate. Good video too with a slight change of style. Really enjoyed it.

👍👍👍 Great stuff. Thanks Karl

Great watch Karl. Loved Jakob sat in the corner at the beginning like some kind of Zen Master 🤷‍♂️😂

Great editing, really chilled vibe of a guy doing what he's good at.

Great job Karl. These are the types of video I love to see you doing. Keep it up 🤛 👏

It was great to see Jakob just sitting there as you were carrying the sheet material in 🤣. Oh and excellent bit of work

Excellent build. Also nice to see 'the boy' hanging around in the background. Although the same cant be said about those hairy legs in those short shorts 😂

Hi Karl, nice alcove units,a great workshop project, Great video take care

Karl, that was superb. I have watched you from your very beginning with RUclips and you have soared to perfection. This vid format was mesmerising. A great build and you made it look so easy. I take my hat off to you mate, regards, Fred

That looks really nice! And the utility of this alcove will be enjoyed for a long time.

Fuck yiutube x x

I like this kind of content. Gives me motivation to sort out some my my own rooms. Jobs ive been putting off for too long! Good stuff Karl 👍🏻

I will never buy an evolution saw because i mentioned it to wife about getting a new cross cut table saw and this ad pops up yiutube fuck that shit.

Warning - I got one of these and the long bottom edge of the razor is not parallel to the base, in fact the angle is easily seen even before I check it with an angle. I was wondering why my first few cuts with it run deeper than needed, and also why it seem to continue cutting when switching the direction 180... any advice about how to remedy this?

Does it insulate heat completely

Looks amazing guys ❤ One problem the weather 😂

Love this - we have wonky doors like this and loose screws - this looks like the answer !!! I also think the hinge may be jiggered but no idea what brand it is - is there a universal hinge? Also are you near to Driffield? Your accent sounds local ! May well call on you if so 😂 thanks for making such a useful and well explained video

at 10:10 with regards to repeatable cuts. With the Rage 5S, you can use the additional fence as a stop block. For safety, fitting the shallow fence, so that the front of it is 3cm's before the blade (it works just like your piece of wood; however, due to it being more secure, it is less likely to get dragged/pulled into the saw). The shallow fence will extend beyond the measuring gauge but not pass the blade.

Just bought one and today after assembling it, I am calibrating it. This is my first table saw. I practised on my friends prior to purchasing and loved it. So now I have my own. I have already got an evolution 2800mm track saw and Evolution DB mitre saw. Brilliant tools.

Hi.what spray can did u use? Thanks

Great video. Can i ask what depth you did the framework for the bar. Im thinking 450mm with 600mm top. Cheers

awesome video, I would recommend Fire Stove Rope around the edge to stop the heat transferring to the wood. I'll give this one a go for my new BBQ, thanks buddy.

No Sugi Ban though?

Great episode dude. Really enjoying the tutorials 🤙